{"product_id":"p6100-oscilloscope-probe-100mhz","title":"P6100 Oscilloscope Probe 100MHz x1\/x10 BNC Repair","description":"\u003ch2\u003eP6100 100MHz Oscilloscope Probe | x1\/x10 Switchable BNC Probe for ASIC Repair Benches\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eP6100 oscilloscope probe\u003c\/strong\u003e is a \u003cstrong\u003e100MHz bandwidth\u003c\/strong\u003e bench probe with \u003cstrong\u003ex1\/x10 switchable attenuation\u003c\/strong\u003e, BNC connector, and standard 1.2m cable — the workhorse scope probe for ASIC miner repair benches that need to measure switching-converter waveforms on PSU and hashboard rails. With \u003cstrong\u003ebackward compatibility to the P6020, P6040, and P6060\u003c\/strong\u003e probe series, the P6100 replaces older or damaged probes on existing scopes without any compensation or signal-path changes.\u003c\/p\u003e\n\u003cp\u003eScope work on mining hardware leans heavily on a clean 100MHz-class probe: PSU PFC switching is in the 65-100kHz range, secondary-side rectifier ringing climbs into the low-MHz range, and ASIC hashboard buck converters operate at 300kHz to 1MHz with ringing tails that need probe bandwidth headroom to capture accurately. The P6100 covers all of these comfortably, and the x10 setting brings the input impedance to 10MΩ for high-impedance probing on sensitive signal nodes.\u003c\/p\u003e\n\u003ch3\u003eWhen You Need the P6100 on the Bench\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePSU output rail ripple measurement\u003c\/strong\u003e — verify ripple stays below the design envelope (typically \u0026lt;100mV pp on 12V rails).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuck-converter switching node observation\u003c\/strong\u003e — diagnose hashboard rail instability or capacitor failure.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLogic-level signal probing\u003c\/strong\u003e on control board GPIO, SPI, I2C, UART — x10 setting protects signal integrity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCrystal oscillator and clock signal verification\u003c\/strong\u003e — check ASIC hash chip clock health.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePFC controller and feedback loop debug\u003c\/strong\u003e — capture switching waveforms and feedback signal dynamics.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecs and Technical Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e100MHz bandwidth\u003c\/strong\u003e — covers PSU PFC switching, secondary rectifier ringing, and ASIC buck-converter switching nodes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ex1 \/ x10 switchable attenuation\u003c\/strong\u003e — x1 for low-signal measurements, x10 for high-impedance probing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBNC connector\u003c\/strong\u003e — standard scope input, compatible with any modern oscilloscope.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1.2m cable length\u003c\/strong\u003e — bench-friendly reach without compromising bandwidth.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e600V CAT II rating\u003c\/strong\u003e — safe for AC mains-side probing on PSU primary stages.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompensation adjustment\u003c\/strong\u003e on the BNC end — tune probe to scope input capacitance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBackward compatible\u003c\/strong\u003e with P6020 \/ P6040 \/ P6060 probe series — drop-in replacement.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eP6100 Oscilloscope Probe Specifications\u003c\/h4\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eFeature\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBandwidth\u003c\/td\u003e\n\u003ctd\u003e100MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAttenuation\u003c\/td\u003e\n\u003ctd\u003ex1 \/ x10 switchable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput Impedance (x10)\u003c\/td\u003e\n\u003ctd\u003e10MΩ\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput Impedance (x1)\u003c\/td\u003e\n\u003ctd\u003e1MΩ\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput Capacitance\u003c\/td\u003e\n\u003ctd\u003eApproximately 14-25pF (x10)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum Input Voltage\u003c\/td\u003e\n\u003ctd\u003e600V CAT II\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCable Length\u003c\/td\u003e\n\u003ctd\u003e1.2m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector\u003c\/td\u003e\n\u003ctd\u003eBNC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompatibility\u003c\/td\u003e\n\u003ctd\u003eBackward-compatible with P6020 \/ P6040 \/ P6060\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompensation Range\u003c\/td\u003e\n\u003ctd\u003e10-35pF (adjustable)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003e\u003c\/h3\u003e\n\u003ch3\u003eFAQ — P6100 Oscilloscope Probe\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Will it work with my oscilloscope?\u003c\/strong\u003e\u003cbr\u003eA: Yes — the P6100 uses a standard BNC connector and works with any oscilloscope that has a BNC input. Most modern scopes accept x10 probes natively; older scopes may require manual selection of the probe ratio in the channel menu.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: How do I compensate the probe?\u003c\/strong\u003e\u003cbr\u003eA: Connect the probe tip to your scope's \"PROBE COMP\" or \"CAL\" output (usually 1kHz square wave). Adjust the screw on the BNC end of the probe with a small flat screwdriver until the square wave is perfectly flat — no overshoot, no undershoot.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: When should I use x1 vs x10?\u003c\/strong\u003e\u003cbr\u003eA: Use x10 for most measurements — it gives 10MΩ input impedance and 100MHz bandwidth. Use x1 only when the signal is below 50mV and noise floor matters more than loading effects (x1 has only 1MΩ and ~6MHz bandwidth on most probes).\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Can I probe AC mains-side circuits?\u003c\/strong\u003e\u003cbr\u003eA: Yes — at the 600V CAT II rating, the P6100 is rated for the primary side of PSUs (up to 250VAC mains). Always reference scope chassis to mains ground or use a differential probe for floating measurements.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQ: Bulk pricing for repair shops?\u003c\/strong\u003e\u003cbr\u003eA: Yes — email contact@lys-sz.com for volume pricing on multi-probe orders.\u003c\/p\u003e\n\u003ch3\u003eRelated products\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/products\/fluke-15b-plus-multimeter-handheld-digital-electrical-test\"\u003eFluke 15B+ Handheld Digital Multimeter\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/whatsminer-test-fixture-m20s-m30s-m31s-m31s-plus-m32-m32s-m40-control-board\"\u003eWhatsminer Test Fixture (M20S\/M30S\/M31S\/M32)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/avalon-a3205-chip-tin-tool-fxiture-a1066-a1046-a1047-hashboard-asic-repair\"\u003eAvalon A3205 Chip Tin Tool Fixture (A1066\/A1046\/A1047)\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/goldshell-test-fixture-hashboard-scanner\"\u003eGoldshell Test Fixture Hashboard Scanner\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eEquipping a new ASIC repair bench? Email \u003ca href=\"mailto:contact@lys-sz.com\"\u003econtact@lys-sz.com\u003c\/a\u003e for volume pricing on scope probes, multimeters, and test fixtures. Worldwide shipping from our Shenzhen warehouse.\u003c\/p\u003e","brand":"LYS Shenzhen","offers":[{"title":"Default Title","offer_id":43183973728435,"sku":null,"price":5.8,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0627\/6710\/4179\/files\/High-Quality-P6100-Oscilloscope-Probe-100MHz.webp?v=1744764259","url":"https:\/\/lys-sz.com\/products\/p6100-oscilloscope-probe-100mhz","provider":"LYS Shenzhen","version":"1.0","type":"link"}