IEC China Standard Plug to 2X C13 Splitter Power Cord 5ft for ASIC Miner Antminer
Couldn't load pickup availability
Have questions about this product? Our team is here to help — just reach out on WhatsApp.
💬 Contact Us on WhatsAppAbout the Product
China Plug to Dual C13 Splitter Power Cord for Bitmain Antminer Mining Setups
The China-standard plug (10-30P) to dual C13 splitter AC power cord takes a single high-current CN-spec outlet and splits it into two C13 female leads — ideal for powering twin Bitmain Antminer PSU inputs from one wall socket or PDU port. The cord is built around a 12/14AWG conductor, sized for the combined current of two small/mid-class ASIC miners.
This splitter is the practical solution when a home or small-farm operator has more miners than wall sockets — instead of running two separate cords across the floor, one heavy-duty cord delivers AC to a pair of C13 inputs from a single 10-30P outlet. Check the upstream breaker and conductor gauge before doubling the load.
Specifications
| Parameter | Value |
|---|---|
| Model | 10-30P to 2x C13 Splitter Power Cord |
| Condition | New |
| Category | AC heavy-duty power cord |
| Wall-side plug | CN standard (10-30P) male |
| PSU-side connectors | 2x C13 female |
| Length | 1.5 meters (5ft) |
| Conductor gauge | 12/14AWG |
| Compatibility | Bitmain Antminer crypto mining PSUs (C13 input) |
| Use case | Single outlet to dual PSU input distribution |
Compatibility
Both C13 ends fit any ASIC miner PSU with a C13 inlet — common on older Bitmain Antminer L3+, S9 and similar units, plus several Avalon and Innosilicon PSUs. The wall-side 10-30P plug requires a CN-spec 250V wall outlet. For US or EU mains, use the matching regional C13 cord listed in related products.
Where the splitter fits
The two C13 connectors plug into the AC inlets of two adjacent PSUs; the 10-30P plug terminates at a single wall socket or PDU port. The 1.5-meter / 5ft length is enough to route between two side-by-side miners. Keep the total current draw across both legs well below the 16A wall socket rating — a single 10-30P breaker is shared across both legs of the splitter.
Common failure symptoms
- One miner powers on, the other does not — broken conductor in one leg
- Splitter overheats at the junction under combined load — undersized for the deployment
- Intermittent shutdowns on both miners simultaneously — loose 10-30P plug
- Burn marks or melted plastic at either C13 housing
- Wall-socket breaker trips at boot — combined inrush current exceeds the 16A rating
Frequently asked questions
Can I run two Antminer S19 / S21 units on this splitter?
No — modern high-power miners draw 14-18A each on a 220V circuit, which exceeds the 16A combined budget of a single 10-30P CN socket. Use one cord per miner for S19 / S21 class hardware. The splitter is best for two lower-power L3+ / S9 / S11 class miners or smaller Avalon / Innosilicon units.
What's the maximum total current I can pull through the splitter?
Treat the upstream 10-30P plug and breaker as the limit. Most CN-spec 10-30P circuits are rated 16A / 250V — keep the combined miner draw below that ceiling.
Will this fit US or EU wall outlets?
No — the 10-30P plug is CN-spec. For US deployments, use a NEMA-to-2xC13 splitter; for EU deployments, use the EU C13 cord and a PDU. See related products.
Can I splice in a third C13 leg?
No. The splitter is built for two legs only. Splicing additional legs is unsafe and voids the conductor sizing.
Related products
- China Plug to C13 Heavy-Duty AC Power Cord 1.5m for Antminer
- US 3-Pin to C19 Power Cord 1.5m for Whatsminer / Avalon
- C13 to C20 PDU Power Cord for Antminer Bitmain PSU
- C13 to C14 Power Cord for Antminer Bitmain PSU
- C19 Female Power Plug Adaptor 250VAC (Replacement Inlet)
Contact contact@lys-sz.com for volume pricing or compatibility questions.Worldwide shipping from our Shenzhen warehouses. DDP available for US and EU customers.
Buying in bulk for a mining farm or repair shop?
Get dedicated B2B pricing on this part and across our full catalog — quote response within 24 hours, payment by T/T USD bank wire, and DDP delivery available for US & EU customers (and other lanes on request).
