Collection: ASIC Miners Control Boards

ASIC Miner Control Boards — Replacement and Repair for Antminer, Whatsminer, Avalon, Iceriver, Goldshell, Innosilicon

The control board is the brain of an ASIC miner — the small Linux SBC that boots the firmware, communicates with the hashboards over a signal cable, and exposes the web interface where you configure pools and monitor performance. When a control board fails (no boot, no IP, kernel panic, persistent restart), the miner produces zero hashrate regardless of how healthy the hashboards are. This collection covers every control board generation we stock for Antminer (Amlogic A113D C76, BB Beaglebone, C87 overclocking), Whatsminer (CB4, CB5, CB6 V10, H6, H3), Avalon (A10 to A15 generation), Iceriver (KS / AL series), Goldshell (CK5/CK6, KD5/KD6, HS5/LT5), and Innosilicon (T2T / T3 / A4+ / A6+ / G-series) — sourced directly from Shenzhen.

Common control board failure modes

Three symptom patterns point to a control board fault rather than a hashboard or PSU issue :

• Miner won't boot, no fan spin-up after power-on — the control board doesn't initialise. Power supply is fine (the LED is on), but nothing happens. Suspect the control board MCU or its boot flash.
• Miner boots but no IP address, no DHCP response, no web UI — network interface failure on the control board, or corrupted bootloader. Sometimes a fresh control board fixes it instantly ; sometimes the control board's signal cable to the network port is the actual culprit (check the cable before replacing the board).
• Persistent restart loop, kernel panic, immediate shutdown after boot — corrupted firmware, failed onboard flash, or a hardware fault on the MCU bus. Generally faster to swap the control board than try to recover the firmware.

What's in this collection

50+ control board SKUs organised by brand and generation :

• Antminer (Bitmain) control boards — Amlogic A113D C76 control board for S19j / S19j Pro / S19 K Pro / S21 / T21 (the dominant board in the current Bitmain fleet), BB Beaglebone control boards for legacy S9 / S17 / L3+ generations, C87 overclocking control board for L7 / S19 series miners, dedicated control board for L3+ / D3, brand new S17 / S17+ / S17e / T17 / T17e / S17 Pro series control board.
• Whatsminer (MicroBT) control boards — CB6 V10 control board for M20s / M21s / M30s / M30 / M31s+ / M32 / M50 (broadest compatibility), CB4 V10 H6 control board for the same generations, CB5 control board for M30 series, CB6 V9 H616 control board for M66S, Whatsminer adapter board V1.3 for D1 / M10 / M20 / M30 series, Whatsminer control board protective case for 4-pin / 6-pin fan configurations.
• Avalon (Canaan) control boards — Avalon control board for 1066 Pro / 1166 Pro / 1126 / 1246 / 1126 Pro / 1248 / 1266 (covers A10 / A11 / A12 generation), updated Avalon control board for A1566 / A1366 / A1346 / A1446 / A1466 (current generation).
• Goldshell control boards — Goldshell CK5 / CK6 control board with model selection, Goldshell KD5 / KD6 control board for Kadena mining, dedicated boards for HS5 / LT5 / LT5 Pro.
• Iceriver control boards — Iceriver control board for KS1 / KS2 / KS3 / KS3M / KS3L / KS5L / KS5M (covers full KAS-mining range).
• Innosilicon control boards — dedicated boards for T2T / T3 / A4+ / A6+ / G-series Innosilicon hardware.

Why source control boards from LYS Shenzhen

Three reasons repair shops and mining farms standardise on our control boards :

• Tested and pre-flashed — every control board ships with the matching firmware pre-loaded for the target miner generation. You install, plug in, and the miner boots ready for network configuration. No firmware flash troubleshooting on top of the hardware swap.
• Genuine boards for current generations — for current Bitmain Amlogic C76, Whatsminer CB6 V10, and Avalon A14 / A15 boards, we source through channels that handle factory-grade hardware. Compatible boards (where supply chain allows) are clearly labelled.
• Bulk pricing for fleet repair — control boards are $24-$140 each ; at 50+ miners with rolling failure rate, fleet repair shops save significant amounts on volume orders. Quote-based pricing reflects bulk. Worldwide shipping with DDP option for US and EU customers.

Frequently asked questions

Will the control board need re-flashing after installation ?
For most current-generation boards (Amlogic C76 for Antminer S19+ / S21, CB6 V10 for Whatsminer M-series), the firmware is pre-loaded and the miner boots out of the box. For some legacy boards (BB Beaglebone for older S9 / S17), you may need to flash via SD card with the matching firmware version. Each product page specifies whether the board is pre-flashed.

Can I use a CB5 control board on an M30s ? Or a CB4 on an M50 ?
Match the board generation to your miner generation. When in doubt, our team can confirm based on your specific model and the existing control board version printed on the failed board.

I tried a new control board and the miner still doesn't boot — what next ?
After a failed control board swap, the next two suspects are : (1) the data cable between control board and hashboard (worn ribbon causes phantom boot failures) and (2) a PSU output voltage out of spec. Test the data cable with a continuity meter and check the PSU output before assuming the new board is also faulty.

Do you stock the C87 overclocking control board for L7 / S19 ?
Yes, the C87 overclocking control board is stocked specifically for users running Antminer L7 and S19 series miners with custom firmware for hashrate boost. Note that overclocking voids warranty and can shorten hashboard lifespan ; we recommend it only for users who understand the trade-off.

Get a custom quote for bulk control boards

For mining farms with fleet-spec inventory or repair shops processing batch control-board swaps, our volume pricing on control boards reflects scale. Send your miner model mix and reorder volume and we'll quote back with options.

Get Business Pricing →