ElphaPex DG1 DG1+ AC Power Cord: C20 to 2 x C19 Splitter to PDU
Couldn't load pickup availability
Have questions about this product? Our team is here to help — just reach out on WhatsApp.
💬 Contact Us on WhatsAppAbout the Product
ElphaPex DG1 / DG1+ AC Power Cord | C20 to Dual C19 Splitter Cable for PDU Distribution
The ElphaPex DG1 / DG1+ AC Power Cord is the splitter cable that connects the dual-input FP-101 PSU to a single PDU outlet. The cord terminates in an IEC C20 male on the PDU side and splits into two C19 female ends on the miner side — one for each of the two AC inputs the DG1 PSU expects. Required accessory whenever you deploy the DG1 in a farm rack that uses C19 PDU outlets rather than separate dual feeds.
Built with a 4mm gauge main cable rated for the combined 4000W load and 1.5mm gauge splitter legs sized for the per-leg 200–240VAC × 10A draw. Total length is 1.5 metres — long enough for typical rack-to-miner runs without coiled excess that creates inductive losses. Strain relief at both junctions for repeated farm-floor handling.
When to Use the DG1 Splitter Power Cord
- Farm racks with C19 PDU outlets — splitter mates a single outlet to the DG1's dual PSU inputs without needing two PDU positions.
- Replacing a damaged factory cord — strain relief or insulation degraded from heat or handling, time to refresh before electrical fault.
- Adding new DG1 / DG1+ units to an existing PDU layout — keeps the deployment density high without re-cabling the rack.
- Spare inventory for farm operators — power cords are first-line wear items, stock spares to keep MTTR low on cabling faults.
ElphaPex DG1 Splitter Power Cord Specifications
| Feature | Specification |
|---|---|
| Compatibility | ElphaPex DG1, DG1+ |
| Connector Type | IEC C20 male to 2× C19 female |
| Total Length | 1.5 m |
| Main Cable Gauge | 4 mm² conductor |
| Splitter Cable Gauge | 1.5 mm² conductor each leg |
| Voltage Rating | 200–240 VAC |
| Current Rating | 10 A per splitter leg (matches PSU input spec) |
| Jacket | Heat-resistant insulated jacket |
| Strain Relief | At both junction points |
| Condition | Brand New |
FAQ — DG1 Splitter Power Cord
Q: Why does the DG1 need a splitter cord at all?
A: The DG1's FP-101 PSU has two independent 200–240VAC × 10A inputs that share the 4000W load. Standard PDUs typically expose a single C19 outlet per circuit, so the splitter lets one PDU outlet feed both PSU inputs from the same circuit.
Q: Can I run the two splitter legs from two different PDU circuits for redundancy?
A: This cord is designed for single-outlet feeding. For dual-circuit redundancy you'd need two separate C19-to-C19 cables instead — email contact@lys-sz.com if that's your deployment.
Q: Is the cord rated for continuous DG1 duty?
A: Yes — the 4mm main and 1.5mm splitter legs are sized for the combined 4000W load (about 17–20 A on the input side at 200V), well within the cord's continuous current rating.
Q: Bulk pricing for farm deployments?
A: Yes — email contact@lys-sz.com with your DG1 count and we'll send case-quantity pricing.
Related products
- ElphaPex FP-101 PSU – DG1 4000W Replacement
- ElphaPex DG1 / DG1+ Brand New Control Board
- ElphaPex FP-102 PSU – DG1 Alternative
- ElphaPex DG1 Fan Speed Simulator
Farm operators stocking DG1 splitter cords by the case? Email contact@lys-sz.com for bulk pricing. Worldwide shipping from our Shenzhen warehouse.
Buying in bulk for a mining farm or repair shop?
Get dedicated B2B pricing on this part and across our full catalog — quote response within 24 hours, payment by T/T USD bank wire, and DDP delivery available for US & EU customers (and other lanes on request).
